1) Where documents are referenced in this Code, they shall be the editions designated in Table 1.3.1.2. (See Appendix A.)
| Table 1.3.1.2. Documents Referenced in the National Building Code of Canada 2005 Forming Part of Sentence 1.3.1.2.(1) |
|||
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| ANSI | A208.1‐1999 | Particleboard, Mat‐Formed Wood | Table 5.10.1.1. 9.23.14.2.(3) 9.29.9.1.(1) 9.30.2.2.(1) |
| ANSI/ASME | B16.3‐1998 | Malleable‐Iron Threaded Fittings | 7.2.6.6.(1) |
| ANSI/ASME | B16.4‐1998 | Gray Iron Threaded Fittings | 7.2.6.5.(1) |
| ANSI/ASME | B16.12‐1998 | Cast‐Iron Threaded Drainage Fittings | 7.2.6.3.(1) |
| ANSI/ASME | B16.15‐1985 | Cast Bronze Threaded Fittings, Classes 125 and 250 | 7.2.7.3.(1) |
| ANSI | B16.18‐2001 | Cast Copper Alloy Solder‐Joint Pressure Fittings | 7.2.7.6.(1) 7.2.7.6.(2) |
| ANSI/ASME | B16.22‐2001 | Wrought Copper and Copper Alloy Solder ‐ Joint Pressure Fittings | 7.2.7.6.(1) |
| ASME | B16.23‐2002 | Cast Copper Alloy Solder Joint Drainage Fittings: DWV | 7.2.7.5.(1) |
| ANSI/ASME | B16.24‐2001 | Cast Copper Alloy Pipe Flanges and Flanged Fittings | 7.2.7.2.(1) |
| ANSI/ASME | B16.26‐1988 | Cast Copper Alloy Fittings for Flared Copper Tubes | 7.2.7.7.(1) 7.2.7.7.(2) |
| ANSI/ASME | B16.29‐2001 | Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings ‐ DWV | 7.2.7.5.(1) |
| ANSI/ASME | B18.6.1‐1981 | Wood Screws (Inch Series) | Table 5.10.1.1. 9.23.3.1.(2) |
| ANSI/ASHRAE | 62‐2001 | Ventilation for Acceptable Indoor Air Quality | 6.2.2.1.(2) |
| ANSI/ASHRAE/IESNA | 90.1‐2004 | Energy Standard for Buildings Except Low‐Rise Residential Buildings | 10.2.1.1.1.(1) Table 10.2.1.1.B |
| ANSI/AWWA | C104/A21.4‐2004 | Cement‐Mortar Lining for Ductile‐Iron Pipe and Fittings for Water | 7.2.6.4.(2) |
| ANSI/AWWA | C110/A21.10‐2003 | Ductile‐Iron and Gray‐Iron Fittings, 3 in. Through 48 in. (75 mm Through 1 200 mm), for Water and Other Liquids | 7.2.6.4.(3) |
| ANSI/AWWA | C111/A21.11‐2000 | Rubber‐Gasket Joints for Ductile‐Iron Pressure Pipe and Fittings | 7.2.6.4.(4) |
| ANSI/AWWA | C151/A21.51‐2002 | Ductile‐Iron Pipe, Centrifugally Cast, for Water | 7.2.6.4.(1) |
| ANSI/CSA | ANSI Z21.22‐1999/CSA 4.4‐M99 | Relief Valves for Hot Water Supply Systems | 7.2.10.11.(1) |
| ANSI/CSA | ANSI Z21.22a‐2000/CSA 4.4a‐2000 | Addenda 1 to ANSI Z21.22‐1999/CSA 4.4‐M99, Relief Valves for Hot Water Supply Systems | 7.2.10.11.(1) |
| ANSI/CSA | ANSI Z21.22b‐2001/CSA 4.4b‐2001 | Addenda 2 to ANSI Z21.22‐1999/CSA 4.4‐M99, Relief Valves for Hot Water Supply Systems | 7.2.10.11.(1) |
| ASSE | 1010‐2004 | Water Hammer Arresters | 7.2.10.15.(1) |
| ASSE | 1051‐2002 | Individual and Branch Type Air Admittance Valves for Sanitary Drainage Systems | 7.2.10.16.(1) |
| ASTM | A 53/A 53M‐02 | Pipe, Steel, Black and Hot‐Dipped, Zinc‐Coated, Welded and Seamless | 7.2.6.7.(4) |
| ASTM | A 123/A 123M‐02 | Zinc (Hot‐Dip Galvanized) Coatings on Iron and Steel Products | Table 5.10.1.1. Table 9.20.16.1. |
| ASTM | A 153/A 153M‐03 | Zinc Coating (Hot‐Dip) on Iron and Steel Hardware | Table 5.10.1.1. Table 9.20.16.1. |
| ASTM | A 252‐98 | Welded and Seamless Steel Pipe Piles | 4.2.3.8.(1) |
| ASTM | A 283/A 283M‐03 | Low and Intermediate Tensile Strength Carbon Steel Plates | 4.2.3.8.(1) |
| ASTM | A 518/A 518M‐99 | Corrosion‐Resistant High‐Silicon Iron Castings | 7.2.8.1.(1) |
| ASTM | A 653/A 653M‐03 | Steel Sheet, Zinc‐Coated (Galvanized) or Zinc‐Iron Alloy‐Coated (Galvannealed) by the Hot‐Dip Process | Table 5.10.1.1. 9.3.3.2.(1) |
| ASTM | A 792/A 792M‐03 | Steel Sheet, 55% Aluminum‐Zinc Alloy‐Coated by the Hot‐Dip Process | 9.3.3.2.(1) |
| ASTM | A 1008/A 1008M‐04 | Steel, Sheet, Cold‐Rolled, Carbon, Structural, High‐Strength Low‐Alloy and High‐Strength Low‐Alloy with Improved Formability | 4.2.3.8.(1) |
| ASTM | A 1011/A 1011M‐03a | Steel, Sheet and Strip, Hot‐Rolled, Carbon, Structural, High‐Strength Low‐Alloy and High‐Strength Low‐Alloy with Improved Formability | 4.2.3.8.(1) |
| ASTM | B 32‐03 | Solder Metal | 7.2.9.2.(1) |
| ASTM | B 42‐02e1 | Seamless Copper Pipe, Standard Sizes | 7.2.7.1.(1) |
| ASTM | B 43‐98e1 | Seamless Red Brass Pipe, Standard Sizes | 7.2.7.1.(2) |
| ASTM | B 88‐03 | Seamless Copper Water Tube | 7.2.7.4.(1) |
| ASTM | B 306‐02 | Copper Drainage Tube (DWV) | 7.2.7.4.(1) |
| ASTM | B 813‐00e1 | Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube | 7.2.9.2.(3) |
| ASTM | B 828‐02 | Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings | 7.3.2.4.(1) |
| ASTM | C 4‐03 | Clay Drain Tile and Perforated Clay Drain Tile | Table 5.10.1.1. 9.14.3.1.(1) |
| ASTM | C 27‐98 | Classification of Fireclay and High‐Alumina Refractory Brick | 9.21.3.4.(1) |
| ASTM | C 36/C 36M‐03 | Gypsum Wallboard | 3.1.5.12.(4) Table 5.10.1.1. 9.29.5.2.(1) |
| ASTM | C 37/C 37M‐01 | Gypsum Lath | Table 5.10.1.1. 9.29.5.2.(1) |
| ASTM | C 79/C 79M‐04 | Treated Core and Nontreated Core Gypsum Sheathing Board | Table 5.10.1.1. Table 9.23.16.2.A. |
| ASTM | C 126‐99 | Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units | Table 5.10.1.1. 9.20.2.1.(1) |
| ASTM | C 212‐00 | Structural Clay Facing Tile | Table 5.10.1.1. 9.20.2.1.(1) |
| ASTM | C 260‐01 | Air‐Entraining Admixtures for Concrete | 9.3.1.8.(1) |
| ASTM | C 411‐97 | Hot‐Surface Performance of High‐Temperature Thermal Insulation | 3.6.5.4.(4) 3.6.5.5.(1) 9.33.6.4.(4) 9.33.8.2.(2) |
| ASTM | C 412M‐03 | Concrete Drain Tile (Metric) | Table 5.10.1.1. 9.14.3.1.(1) |
| ASTM | C 442/C 442M‐04 | Gypsum Backing Board, Gypsum Coreboard, and Gypsum Shaftliner Board | 3.1.5.12.(4) Table 5.10.1.1. 9.29.5.2.(1) |
| ASTM | C 444M‐03 | Perforated Concrete Pipe (Metric) | Table 5.10.1.1. 9.14.3.1.(1) |
| ASTM | C 494/C 494M‐04 | Chemical Admixtures for Concrete | 9.3.1.8.(1) |
| ASTM | C 588/C 588M‐03 | Gypsum Base for Veneer Plasters | 3.1.5.12.(4) Table 5.10.1.1. 9.29.5.2.(1) |
| ASTM | C 630/C 630M‐03 | Water‐Resistant Gypsum Backing Board | 3.1.5.12.(4) Table 5.10.1.1. 9.29.5.2.(1) |
| ASTM | C 700‐02 | Vitrified Clay Pipe, Extra Strength, Standard Strength and Perforated | Table 5.10.1.1. 9.14.3.1.(1) |
| ASTM | C 931/C 931M‐04 | Exterior Gypsum Soffit Board | 3.1.5.12.(4) Table 5.10.1.1. 9.29.5.2.(1) |
| ASTM | C 960/C 960M‐04 | Predecorated Gypsum Board | 3.1.5.12.(4) Table 5.10.1.1. 9.29.5.2.(1) |
| ASTM | C 1002‐01 | Steel Self‐Piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs | Table 5.10.1.1. 9.24.1.4.(1) 9.29.5.7.(1) |
| ASTM | C 1053‐00 | Borosilicate Glass Pipe and Fittings for Drain, Waste, and Vent (DWV) Applications | 7.2.8.1.(1) |
| ASTM | C 1177/C 1177M‐04e1 | Glass Mat Gypsum Substrate for Use as Sheathing | Table 5.10.1.1. Table 9.23.16.2.A. |
| ASTM | C 1178/C 1178M‐04 | Glass Mat Water‐Resistant Gypsum Backing Panel | Table 5.10.1.1. 9.29.5.2.(1) |
| ASTM | C 1395/C 1395M‐04 | Gypsum Ceiling Board | Table 5.10.1.1. 9.29.5.2.(1) |
| ASTM | C 1396/C 1396M‐03a | Gypsum Board | Table 5.10.1.1. 9.29.5.2.(1) |
| ASTM | D 323‐99a | Vapor Pressure of Petroleum Products (Reid Method) | 1.4.1.2.(1) () |
| ASTM | D 2178‐97a | Asphalt Glass Felt Used in Roofing and Waterproofing | Table 5.10.1.1. |
| ASTM | D 2466‐02 | Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 | 7.2.5.8.(2) |
| ASTM | D 2467‐02 | Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 | 7.2.5.8.(2) |
| ASTM | D 2898‐94 | Accelerated Weathering of Fire‐Retardant‐Treated Wood for Fire Testing | 3.1.5.5.(4) 3.1.5.21.(1) 3.2.2.45.(3) |
| ASTM | D 3261‐03 | Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing | 7.2.5.5.(3) |
| ASTM | E 90‐04 | Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements | 5.9.1.1.(1) 9.11.1.1.(1) |
| ASTM | E 96‐00e1 | Water Vapor Transmission of Materials | 5.5.1.2.(3) 9.25.1.2.(1) 9.25.4.2.(1) 9.30.1.2.(1) |
| ASTM | E 336‐97e1 | Measurement of Airborne Sound Insulation in Buildings | 5.9.1.1.(1) 9.11.1.1.(1) |
| ASTM | E 413‐87 | Classification for Rating Sound Insulation | 5.9.1.1.(1) 9.11.1.1.(1) |
| ASTM | F 476‐84 | Security of Swinging Door Assemblies | 9.6.8.10.(1) |
| ASTM | F 628‐01 | Acrylonitrile‐Butadiene‐Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core | 7.2.5.10.(1), 7.2.5.12.(1) |
| ASTM | F 714‐03 | Polyethylene (PE) Plastic Pipe (SDR‐PR) Based on Outside Diameter | 7.2.5.6.(1) |
| AWPA | M4‐02 | Care of Preservative‐Treated Wood Products | 4.2.3.2.(2) Table 5.10.1.1. |
| BNQ | NQ 3624‐115‐2000 | Polyethylene (PE) Pipe and Fittings ‐ Flexible Corrugated Pipes for Drainage ‐ Characteristics and Test Methods | Table 5.10.1.1. 9.14.3.1.(1) |
| CGSB | CAN/CGSB‐1.501‐M89 | Method for Permeance of Coated Wallboard | 5.5.1.2.(2) 9.25.4.2.(6) |
| CGSB | CAN/CGSB‐7.1‐98 | Lightweight Steel Wall Framing Components | 9.24.1.2.(1) |
| CGSB | CAN/CGSB‐7.2‐97 | Adjustable Steel Columns | 9.17.3.4.(1) |
| CGSB | CAN/CGSB‐10.3‐92 | Air Setting Refractory Mortar | 9.21.3.4.(2) 9.21.3.9.(1) 9.22.2.2.(2) |
| CGSB | CAN/CGSB‐11.3‐M87 | Hardboard | Table 5.10.1.1. 9.27.10.1.(2) 9.29.7.1.(1) 9.30.2.2.(1) |
| CGSB | CAN/CGSB‐11.5‐M87 | Hardboard, Precoated, Factory Finished, for Exterior Cladding | Table 5.10.1.1. 9.27.10.1.(1) |
| CGSB | CAN/CGSB‐12.1‐M90 | Tempered or Laminated Safety Glass | 3.3.1.19.(2) 3.4.6.14.(1) 3.4.6.14.(3) Table 5.10.1.1. 9.6.6.2.(2) 9.7.3.1.(1) 9.8.8.7.(1) |
| CGSB | CAN/CGSB‐12.2‐M91 | Flat, Clear Sheet Glass | Table 5.10.1.1. 9.7.3.1.(1) |
| CGSB | CAN/CGSB‐12.3‐M91 | Flat, Clear Float Glass | Table 5.10.1.1. 9.7.3.1.(1) |
| CGSB | CAN/CGSB‐12.4‐M91 | Heat Absorbing Glass | Table 5.10.1.1. 9.7.3.1.(1) |
| CGSB | CAN/CGSB‐12.8‐97 | Insulating Glass Units | Table 5.10.1.1. 9.7.3.1.(1) |
| CGSB | CAN/CGSB‐12.10‐M76 | Glass, Light and Heat Reflecting | Table 5.10.1.1. 9.7.3.1.(1) |
| CGSB | CAN/CGSB‐12.11‐M90 | Wired Safety Glass | 3.3.1.19.(2) 3.4.6.14.(1) 3.4.6.14.(3) Table 5.10.1.1. 9.6.6.2.(2) 9.7.3.1.(1) 9.8.8.7.(1) |
| CGSB | CAN/CGSB‐12.20‐M89 | Structural Design of Glass for Buildings | 4.3.6.1.(1) 9.7.3.2.(1) |
| CGSB | 19‐GP‐5M‐1984 | Sealing Compound, One Component, Acrylic Base, Solvent Curing | Table 5.10.1.1. 9.27.4.2.(2) |
| CGSB | CAN/CGSB‐19.13‐M87 | Sealing Compound, One‐Component, Elastomeric, Chemical Curing | Table 5.10.1.1. 9.27.4.2.(2) |
| CGSB | 19‐GP‐14M‐1984 | Sealing Compound, One Component, Butyl‐Polyisobutylene Polymer Base, Solvent Curing | Table 5.10.1.1. 9.27.4.2.(2) |
| CGSB | CAN/CGSB‐19.22‐M89 | Mildew‐Resistant Sealing Compound for Tubs and Tiles | 9.29.10.5.(1) |
| CGSB | CAN/CGSB‐19.24‐M90 | Multicomponent, Chemical‐Curing Sealing Compound | Table 5.10.1.1. 9.27.4.2.(2) |
| CGSB | CAN/CGSB‐34.1‐94 | Asbestos‐Cement Pressure Pipe | 7.2.5.2.(1) |
| CGSB | CAN/CGSB‐34.4‐M89 | Siding, Asbestos‐Cement, Shingles and Clapboards | Table 5.10.1.1. 9.27.8.1.(1) |
| CGSB | CAN/CGSB‐34.5‐M89 | Sheets, Asbestos‐Cement, Corrugated | Table 5.10.1.1. 9.27.8.1.(1) |
| CGSB | CAN/CGSB‐34.9‐94 | Asbestos‐Cement Sewer Pipe | 7.2.5.1.(2) |
| CGSB | CAN/CGSB‐34.14‐M89 | Sheets, Asbestos‐Cement, Decorative | Table 5.10.1.1. 9.27.8.1.(1) |
| CGSB | CAN/CGSB‐34.16‐M89 | Sheets, Asbestos‐Cement, Flat, Fully Compressed | Table 5.10.1.1. 9.27.8.1.(1) |
| CGSB | CAN/CGSB‐34.17‐M89 | Sheets, Asbestos‐Cement, Flat, Semicompressed | Table 5.10.1.1. 9.27.8.1.(1) |
| CGSB | CAN/CGSB‐34.21‐M89 | Panels, Sandwich, Asbestos‐Cement with Insulating Cores | Table 5.10.1.1. 9.27.8.1.(1) |
| CGSB | CAN/CGSB‐34.22‐94 | Asbestos‐Cement Drain Pipe | Table 5.10.1.1. 9.14.3.1.(1) |
| CGSB | CAN/CGSB‐34.22‐94 | Asbestos‐Cement Drain Pipe | 7.2.5.1.(1) |
| CGSB | CAN/CGSB‐34.23‐94 | Asbestos‐Cement House Connection Sewer Pipe | 7.2.5.1.(2) |
| CGSB | CAN/CGSB‐37.1‐M89 | Chemical Emulsifier Type, Emulsified Asphalt for Dampproofing | Table 5.10.1.1. 9.13.2.2.(1) |
| CGSB | CAN/CGSB‐37.2‐M88 | Emulsified Asphalt, Mineral‐Colloid Type, Unfilled, for Dampproofing and Waterproofing and for Roof Coatings | Table 5.10.1.1. 9.13.2.2.(1) 9.13.3.2.(1) |
| CGSB | CAN/CGSB‐37.3‐M89 | Application of Emulsified Asphalts for Dampproofing or Waterproofing | 5.8.2.3.(1) Table 5.10.1.1. 9.13.2.3.(1) 9.13.3.3.(1) |
| CGSB | CAN/CGSB‐37.4‐M89 | Fibrated, Cutback Asphalt, Lap Cement for Asphalt Roofing | Table 5.10.1.1. 9.26.2.1.(1) |
| CGSB | CAN/CGSB‐37.5‐M89 | Cutback Asphalt Plastic, Cement | Table 5.10.1.1. 9.26.2.1.(1) |
| CGSB | 37‐GP‐6Ma‐1983 | Asphalt, Cutback, Unfilled, for Dampproofing | 5.8.2.2.(6) 5.8.2.2.(7) Table 5.10.1.1. 9.13.2.2.(1) |
| CGSB | CAN/CGSB‐37.8‐M88 | Asphalt, Cutback, Filled, for Roof Coating | Table 5.10.1.1. 9.26.2.1.(1) |
| CGSB | 37‐GP‐9Ma‐1983 | Primer, Asphalt, Unfilled, for Asphalt Roofing, Dampproofing and Waterproofing | Table 5.10.1.1. 9.26.2.1.(1) |
| CGSB | 37‐GP‐12Ma‐1984 | Application of Unfilled Cutback Asphalt for Dampproofing | 5.8.2.3.(2) Table 5.10.1.1. 9.13.2.3.(1) |
| CGSB | CAN/CGSB‐37.16‐M89 | Filled, Cutback Asphalt for Dampproofing and Waterproofing | Table 5.10.1.1. 9.13.2.2.(1) 9.13.3.2.(1) |
| CGSB | 37‐GP‐18Ma‐1985 | Tar, Cutback, Unfilled, for Dampproofing | 5.8.2.2.(6) 5.8.2.2.(7) Table 5.10.1.1. 9.13.2.2.(1) |
| CGSB | 37‐GP‐21M‐1985 | Tar, Cutback, Fibrated, for Roof Coating | Table 5.10.1.1. 9.26.2.1.(1) |
| CGSB | CAN/CGSB‐37.22‐M89 | Application of Unfilled, Cutback Tar Foundation Coating for Dampproofing | 5.8.2.3.(2) Table 5.10.1.1. 9.13.2.3.(1) |
| CGSB | 37‐GP‐36M 1976 | Application of Filled Cutback Asphalts for Dampproofing and Waterproofing | 5.8.2.3.(1) Table 5.10.1.1. |
| CGSB | 37‐GP‐37M 1977 | Application of Hot Asphalt for Dampproofing or Waterproofing | 5.8.2.3.(1) Table 5.10.1.1. |
| CGSB | CAN/CGSB‐37.50‐M89 | Hot‐Applied, Rubberized Asphalt for Roofing and Waterproofing | Table 5.10.1.1. 9.26.2.1.(1) |
| CGSB | CAN/CGSB‐37.51‐M90 | Application for Hot‐Applied Rubberized Asphalt for Roofing and Waterproofing | 5.6.1.3.(1) 5.8.2.3.(1) Table 5.10.1.1. 9.26.15.1.(1) |
| CGSB | 37‐GP‐52M‐1984 | Roofing and Waterproofing Membrane, Sheet Applied, Elastomeric | Table 5.10.1.1. 9.26.2.1.(1) |
| CGSB | CAN/CGSB‐37.54‐95 | Polyvinyl Chloride Roofing and Waterproofing Membrane | Table 5.10.1.1. 9.26.2.1.(1) |
| CGSB | 37‐GP‐55M‐1979 | Application of Sheet Applied Flexible Polyvinyl Chloride Roofing Membrane | 5.6.1.3.(1) Table 5.10.1.1. 9.26.16.1.(1) |
| CGSB | 37‐GP‐56M‐1985 | Membrane, Modified, Bituminous, Prefabricated, and Reinforced for Roofing | Table 5.10.1.1. 9.26.2.1.(1) |
| CGSB | 37‐GP‐64M‐1977 | Mat Reinforcing, Fibrous Glass, for Membrane Waterproofing Systems and Built‐Up Roofing | Table 5.10.1.1. |
| CGSB | 41‐GP‐6M‐1983 | Sheets, Thermosetting Polyester Plastics, Glass Fiber Reinforced | Table 5.10.1.1. 9.26.2.1.(1) |
| CGSB | CAN/CGSB‐41.24‐95 | Rigid Vinyl Siding, Soffits and Fascia | Table 5.10.1.1. 9.27.13.1.(1) |
| CGSB | CAN/CGSB‐51.25‐M87 | Thermal Insulation, Phenolic, Faced | Table 5.10.1.1. Table 9.23.16.2.A. 9.25.2.2.(1) |
| CGSB | 51‐GP‐27M‐1979 | Thermal Insulation, Polystyrene, Loose Fill | Table 5.10.1.1. 9.25.2.2.(1) |
| CGSB | CAN/CGSB‐51.32‐M77 | Sheathing, Membrane, Breather Type | Table 5.10.1.1. 9.20.13.9.(1) 9.26.2.1.(1) 9.27.3.2.(1) |
| CGSB | CAN/CGSB‐51.33‐M89 | Vapour Barrier Sheet, Excluding Polyethylene, for Use in Building Construction | Table 5.10.1.1. 9.25.4.2.(5) |
| CGSB | CAN/CGSB‐51.34‐M86(Amended 1988) | Vapour Barrier, Polyethylene Sheet for Use in Building Construction | Table 5.10.1.1. 9.13.2.2.(1) 9.13.4.2.(1) 9.18.6.2.(1) 9.25.3.2.(2) 9.25.4.2.(4) |
| CGSB | CAN/CGSB‐63.14‐M89 | Plastic Skylights | 5.10.1.1.(4) Table 5.10.1.1. 9.7.7.1.(1) 9.7.7.2.(1) |
| CGSB | CAN/CGSB‐82.1‐M89 | Sliding Doors | Table 5.10.1.1. 9.6.5.2.(1) |
| CGSB | CAN/CGSB‐82.5‐M88 | Insulated Steel Doors | Table 5.10.1.1. 9.6.5.3.(1) |
| CGSB | CAN/CGSB‐82.6‐M86 | Doors, Mirrored Glass, Sliding or Folding, Wardrobe | 9.6.6.3.(1) |
| CGSB | CAN/CGSB‐93.1‐M85 | Sheet, Aluminum Alloy, Prefinished, Residential | Table 5.10.1.1. 9.27.12.1.(4) |
| CGSB | CAN/CGSB‐93.2‐M91 | Prefinished Aluminum Siding, Soffits and Fascia, for Residential Use | Table 5.10.1.1. 9.27.12.1.(3) |
| CGSB | CAN/CGSB‐93.3‐M91 | Prefinished Galvanized and Aluminum‐Zinc Alloy Steel Sheet for Residential Use | Table 5.10.1.1. 9.27.12.1.(2) |
| CGSB | CAN/CGSB‐93.4‐92 | Galvanized Steel and Aluminum‐Zinc Alloy Coated Steel Siding, Soffits and Fascia, Prefinished, Residential | Table 5.10.1.1. 9.27.12.1.(1) |
| CSA | CAN/CSA‐6.19‐01 | Residential Carbon Monoxide Alarming Devices | 6.2.4.1.(2) |
| CSA | A23.1‐09 | Concrete Materials and Methods of Concrete Construction | 4.2.3.6.(1) 4.2.3.9.(1) Table 5.10.1.1. 9.3.1.1.(1) 9.3.1.1.(4) 9.3.1.3.(1) 9.3.1.4.(1) |
| CSA | A23.3‐04 | Design of Concrete Structures | Table 4.1.8.9. 4.3.3.1.(1) |
| CSA | A60.1‐M1976 | Vitrified Clay Pipe | 7.2.5.4.(1) |
| CSA | A60.3‐M1976 | Vitrified Clay Pipe Joints | 7.2.5.4.(2) |
| CSA | CAN/CSA‐A82.1‐M87 | Burned Clay Brick (Solid Masonry Units Made from Clay or Shale) | Table 5.10.1.1. 9.20.2.1.(1) |
| CSA | A82.3‐M1978 | Calcium Silicate (Sand‐Lime) Building Brick | Table 5.10.1.1. 9.20.2.1.(1) |
| CSA | A82.4‐M1978 | Structural Clay Load‐Bearing Wall Tile | Table 5.10.1.1. 9.20.2.1.(1) |
| CSA | A82.5‐M1978 | Structural Clay Non‐Load‐Bearing Tile | Table 5.10.1.1. 9.20.2.1.(1) |
| CSA | CAN3‐A82.8‐M78 | Hollow Clay Brick | Table 5.10.1.1. 9.20.2.1.(1) |
| CSA | CAN/CSA‐A82.27‐M91 | Gypsum Board | 3.1.5.12.(4) Table 5.10.1.1. Table 9.23.16.2.A. 9.29.5.2.(1) |
| CSA | A82.30‐M1980 | Interior Furring, Lathing and Gypsum Plastering | Table 5.10.1.1. 9.29.4.1.(1) |
| CSA | A82.31‐M1980 | Gypsum Board Application | Table 5.10.1.1. 9.10.12.4.(3) 9.29.5.1.(2) |
| CSA | CAN3‐A93‐M82 | Natural Airflow Ventilators for Buildings | Table 5.10.1.1. 9.19.1.2.(5) |
| CSA | CAN/CSA‐A123.1‐98 | Asphalt Shingles Made From Organic Felt and Surfaced with Mineral Granules | Table 5.10.1.1. 9.26.2.1.(1) |
| CSA | A123.2‐03 | Asphalt‐Coated Roofing Sheets | Table 5.10.1.1. 9.26.2.1.(1) |
| CSA | CAN/CSA‐A123.3‐98 | Asphalt Saturated Organic Roofing Felt | Table 5.10.1.1. 9.26.2.1.(1) |
| CSA | CAN/CSA‐A123.4‐04 | Asphalt for Constructing Built‐Up Roof Coverings and Waterproofing Systems | Table 5.10.1.1. 9.13.2.2.(1) 9.13.3.2.(1) 9.26.2.1.(1) |
| CSA | CAN/CSA‐A123.5‐98 | Asphalt Shingles Made From Glass Felt and Surfaced with Mineral Granules | Table 5.10.1.1. 9.26.2.1.(1) |
| CSA | A123.17‐1963 | Asphalt‐Saturated Felted Glass‐Fibre Mat for Use in Construction of Built‐Up Roofs | Table 5.10.1.1. 9.26.2.1.(1) |
| CSA | CAN3‐A123.51‐M85 | Asphalt Shingle Application on Roof Slopes 1:3 and Steeper | 5.6.1.3.(1) Table 5.10.1.1. 9.26.1.2.(1) |
| CSA | CAN3‐A123.52‐M85 | Asphalt Shingle Application on Roof Slopes 1:6 to Less Than 1:3 | 5.6.1.3.(1) Table 5.10.1.1. 9.26.1.2.(1) |
| CSA | A165.1‐04 | Concrete Block Masonry Units | Table 5.10.1.1. 9.15.2.2.(1) 9.17.5.1.(1) 9.20.2.1.(1) 9.20.2.6.(1) |
| CSA | A165.2‐04 | Concrete Brick Masonry Units | Table 5.10.1.1. 9.20.2.1.(1) |
| CSA | A165.3‐04 | Prefaced Concrete Masonry Units | Table 5.10.1.1. 9.20.2.1.(1) |
| CSA | CAN3‐A165.4‐M85 | Autoclaved Cellular Units | Table 5.10.1.1. 9.20.2.1.(1) |
| CSA | A179‐04 | Mortar and Grout for Unit Masonry | Table 5.10.1.1. 9.15.2.2.(3) 9.20.3.1.(1) |
| CSA | CAN/CSA‐A220.0‐M91 | Performance of Concrete Roof Tiles | Table 5.10.1.1. 9.26.2.1.(1) |
| CSA | CAN/CSA‐A220.1‐M91 | Installation of Concrete Roof Tiles | Table 5.10.1.1. 9.26.17.1.(1) |
| CSA | A257.1‐03 | Non‐Reinforced Circular Concrete Culvert, Storm Drain, Sewer Pipe, and Fittings | 7.2.5.3.(1) |
| CSA | A257.2‐03 | Reinforced Circular Concrete Culvert, Storm Drain, Sewer Pipe, and Fittings | 7.2.5.3.(1) |
| CSA | A257.3‐03 | Joints for Circular Concrete Sewer and Culvert Pipe, Manhole Sections, and Fittings Using Rubber Gaskets | 7.2.5.3.(2) |
| CSA | A257.4‐03 | Precast Reinforced Circular Concrete Manhole Sections, Catch Basins, and Fittings | 7.2.5.3.(5) |
| CSA | CAN/CSA‐A277‐01 | Procedure for Certification of Factory‐Built Houses | 1.1.1.1.(1) |
| CSA | CAN/CSA‐A324‐M88 | Clay Flue Liners | 9.21.3.3.(1) |
| CSA | A371‐04 | Masonry Construction for Buildings | 5.6.1.3.(2) Table 5.10.1.1. 9.15.2.2.(3) 9.20.3.2.(7) 9.20.15.2.(1) |
| CSA | CAN/CSA‐A405‐M87 | Design and Construction of Masonry Chimneys and Fireplaces | 9.21.3.5.(1) 9.22.1.4.(1) 9.22.5.2.(2) |
| CSA | CAN/CSA‐A440‐00 | Windows | 5.10.1.1.(3) Table 5.10.1.1. 9.7.2.1.(1) 9.7.2.1.(2) 9.7.6.1.(1) |
| CSA | CAN/CSA‐A440.1‐00 | User Selection Guide to CSA Standard CAN/CSA‐A440‐00, Windows | 5.10.1.1.(3) Table 5.10.1.1. 9.7.2.1.(1) |
| CSA | A660‐04 | Certification of Manufacturers of Steel Building Systems | 4.3.4.3.(1) |
| CSA | A3001‐08 | Cementitious Materials for Use in Concrete | Table 5.10.1.1. 9.3.1.2.(1) 9.28.2.1.(1) |
| CSA | B44‐00 | Safety Code for Elevators | 3.2.6.7.(2) 3.5.2.1.(2) 3.5.2.1.(3) 3.5.4.2.(1) Table 4.1.5.12. |
| CSA | CAN/CSA‐B45 Series‐02 | Plumbing Fixtures | 7.2.2.2.(1) |
| CSA | CAN/CSA‐B45.1‐02 | Ceramic Plumbing Fixtures | 7.2.2.2.(2) |
| CSA | CAN/CSA‐B45.2‐02 | Enamelled Cast Iron Plumbing Fixtures | 7.2.2.2.(3) |
| CSA | CAN/CSA‐B45.3‐02 | Porcelain‐Enamelled Steel Plumbing Fixtures | 7.2.2.2.(4) |
| CSA | CAN/CSA‐B45.4‐02 | Stainless Steel Plumbing Fixtures | 7.2.2.2.(5) |
| CSA | CAN/CSA‐B45.5‐02 | Plastic Plumbing Fixtures | 7.2.2.2.(6) |
| CSA | CAN/CSA‐B45.9‐02 | Macerating Systems and Related Components | 7.2.2.2.(8) |
| CSA | CAN/CSA‐B45.10‐01 | Hydromassage Bathtubs | 7.2.2.2.(7) |
| CSA | CAN/CSA‐B64.0‐01 | Definitions, General Requirements, and Test Methods for Vacuum Breakers and Backflow Preventers | 7.2.10.10.(1) |
| CSA | CAN/CSA‐B64.1.1‐01 | Vacuum Breakers, Atmospheric Type (AVB) | 7.2.10.10.(1) |
| CSA | CAN/CSA‐B64.1.2‐01 | Vacuum Breakers, Pressure Type (PVB) | 7.2.10.10.(1) |
| CSA | CAN/CSA‐B64.2‐01 | Vacuum Breakers, Hose Connection Type (HCVB) | 7.2.10.10.(1) |
| CSA | CAN/CSA‐B64.2.1‐01 | Vacuum Breakers, Hose Connection Type (HCVB) with Manual Draining Feature | 7.2.10.10.(1) |
| CSA | CAN/CSA‐B64.2.2‐01 | Vacuum Breakers, Hose Connection Type (HCVB) with Automatic Draining Feature | 7.2.10.10.(1) |
| CSA | CAN/CSA‐B64.3‐01 | Backflow Preventers, Dual Check Valve Type with Atmospheric Port (DCAP) | 7.2.10.10.(1) |
| CSA | CAN/CSA‐B64.4‐01 | Backflow Preventers, Reduced Pressure Principle Type (RP) | 7.2.10.10.(1) |
| CSA | CAN/CSA‐B64.4.1‐01 | Backflow Preventers, Reduced Pressure Principle Type for Fire Systems (RPF) | 7.6.2.4.(2) 7.6.2.4.(4) |
| CSA | CAN/CSA‐B64.5‐01 | Backflow Preventers, Double Check Valve Type (DCVA) | 7.2.10.10.(1) |
| CSA | CAN/CSA‐B64.5.1‐01 | Backflow Preventers, Double Check Valve Type for Fire Systems (DCVAF) | 7.6.2.4.(2) |
| CSA | CAN/CSA‐B64.6‐01 | Backflow Preventers, Dual Check Valve Type (DuC) | 7.2.10.10.(1) |
| CSA | CAN/CSA‐B64.6.1‐01 | Backflow Preventers, Dual Check Valve Type for Fire Systems (DuCF) | 7.6.2.4.(2) |
| CSA | CAN/CSA‐B64.7‐01 | Vacuum Breakers, Laboratory Faucet Type (LFVB) | 7.2.10.10.(1) |
| CSA | CAN/CSA‐B64.8‐01 | Backflow Preventers, Dual Check Valve Type with Intermediate Vent (DuCV) | 7.2.10.10.(1) |
| CSA | CAN/CSA‐B64.9‐01 | Backflow Preventers, Single Check Valve Type for Fire Systems (SCVAF) | 7.6.2.4.(2) |
| CSA | CAN/CSA‐B64.10‐01 | Manual for the Selection and Installation of Backflow Prevention Devices | 7.6.2.1.(3) |
| CSA | CAN/CSA‐B70‐02 | Cast Iron Soil Pipe, Fittings, and Means of Joining | 7.2.6.1.(1) 7.4.6.4.(2) |
| CSA | CAN/CSA‐B72‐M87 | Installation Code for Lightning Protection Systems | 6.3.1.4.(1) |
| CSA | B111‐1974 | Wire Nails, Spikes and Staples | 9.23.3.1.(1) 9.26.2.2.(1) 9.29.5.6.(1) |
| CSA | CAN/CSA‐B125‐01 | Plumbing Fittings | 7.2.3.3.(1) 7.2.10.6.(1) 7.2.10.7.(1) 7.2.10.7.(2) 7.2.10.10.(2) |
| CSA | B127.1‐99 | Asbestos Cement Drain, Waste and Vent Pipe and Pipe Fittings | 7.2.5.1.(1) 7.2.6.2.(1) |
| CSA | B127.2‐M1977 | Components for Use in Asbestos Cement Building Sewer Systems | 7.2.5.1.(2) 7.2.6.2.(1) |
| CSA | CAN/CSA‐B137.1‐02 | Polyethylene Pipe, Tubing, and Fittings for Cold‐Water Pressure Services | 7.2.5.5.(1) |
| CSA | CAN/CSA‐B137.2‐02 | PVC Injection‐Moulded Gasketed Fittings for Pressure Applications | 7.2.5.8.(3) |
| CSA | CAN/CSA‐B137.3‐02 | Rigid Polyvinyl Chloride (PVC) Pipe for Pressure Applications | 7.2.5.8.(1) |
| CSA | CAN/CSA‐B137.5‐02 | Crosslinked Polyethylene (PEX) Tubing Systems for Pressure Applications | 7.2.5.7.(1) |
| CSA | CAN/CSA‐B137.6‐02 | CPVC Pipe, Tubing, and Fittings for Hot‐ and Cold‐Water Distribution Systems | 7.2.5.9.(1) |
| CSA | B137.9‐99 | Polyethylene/Aluminum/Polyethylene Composite Pressure‐Pipe Systems | 7.2.5.13.(1) |
| CSA | CAN/CSA‐B137.10‐02 | Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure‐Pipe Systems | 7.2.5.14.(1) |
| CSA | CAN/CSA‐B137.11‐02 | Polypropylene (PP‐R) Pipe and Fittings for Pressure Applications | 7.2.5.15.(1) |
| CSA | CAN/CSA‐B139‐04 | Installation Code for Oil‐Burning Equipment | 6.2.1.4.(1) 9.31.6.2.(2) 9.33.5.2.(1) |
| CSA | B158.1‐1976 | Cast Brass Solder Joint Drainage, Waste and Vent Fittings | 7.2.10.1.(1) |
| CSA | CAN/CSA‐B181.1‐02 | ABS Drain, Waste, and Vent Pipe and Pipe Fittings | 7.2.5.10.(1) 7.2.5.11.(1) 7.2.5.12.(1) 7.4.6.4.(2) |
| CSA | CAN/CSA‐B181.2‐02 | PVC Drain, Waste, and Vent Pipe and Pipe Fittings | 7.2.5.10.(1) 7.2.5.11.(1) 7.2.5.12.(1) 7.4.6.4.(2) |
| CSA | CAN/CSA‐B181.3‐02 | Polyolefin Laboratory Drainage Systems | 7.2.8.1.(1) |
| CSA | CAN/CSA‐B182.1‐02 | Plastic Drain and Sewer Pipe and Pipe Fittings | Table 5.10.1.1. 7.2.5.10.(1) 7.4.6.4.(2) 9.14.3.1.(1) |
| CSA | CAN/CSA‐B182.2‐02 | PVC Sewer Pipe and Fittings (PSM Type) | 7.2.5.10.(1) |
| CSA | CAN/CSA‐B182.4‐02 | Profile PVC Sewer Pipe and Fittings | 7.2.5.10.(1) |
| CSA | CAN/CSA‐B182.6‐02 | Profile Polyethylene Sewer Pipe and Fittings For Leak‐Proof Sewer Applications | 7.2.5.10.(1) |
| CSA | CAN/CSA‐B182.7‐02 | Multilayer PVC Sewer Pipe (PSM Type) Having Reprocessed‐Recycled Content | 7.2.5.10.(1) |
| CSA | CAN/CSA‐B214‐01 | Installation Code for Hydronic Heating Systems | 6.2.1.1.(1) |
| CSA | B242‐M1980 | Groove and Shoulder Type Mechanical Pipe Couplings | 7.2.10.4.(1) |
| CSA | B272‐93 | Prefabricated Self‐Sealing Roof Vent Flashings | 7.2.10.14.(2) |
| CSA | CAN/CSA‐B355‐00 | Lifts for Persons with Physical Disabilities | 3.8.3.10.(1) |
| CSA | CAN/CSA‐B356‐00 | Water Pressure Reducing Valves for Domestic Water Supply Systems | 7.2.10.12.(1) |
| CSA | CAN/CSA‐B365‐01 | Installation Code for Solid‐Fuel‐Burning Appliances and Equipment | 6.2.1.4.(1) 9.22.10.2.(1) 9.31.6.2.(2) 9.33.5.3.(1) |
| CSA | CAN/CSA‐B602‐99 | Mechanical Couplings for Drain, Waste, and Vent Pipe and Sewer Pipe | 7.2.10.4.(2) |
| CSA | C22.2 No. 0.3‐01 | Test Methods for Electrical Wires and Cables | 3.1.4.3.(1) 3.1.5.18.(1) 3.6.4.3.(1) |
| CSA | C22.2 No.141‐02 | Unit Equipment for Emergency Lighting | 3.2.7.4.(2) 9.9.11.3.(6) |
| CSA | C22.2 No. 211.0‐03 | General Requirements and Methods of Testing for Nonmetallic Conduit | 3.1.5.20.(1) |
| CSA | CAN/CSA‐C282‐05 | Emergency Electrical Power Supply for Buildings | 3.2.7.5.(1) |
| CSA | CAN/CSA‐C448 Series‐02 | Design and Installation of Earth Energy Systems | 9.33.5.2.(1) |
| CSA | CAN/CSA‐F280‐M90 | Determining the Required Capacity of Residential Space Heating and Cooling Appliances | 9.33.5.1.(1) |
| CSA | CAN/CSA‐F326‐M91 | Residential Mechanical Ventilation Systems | 9.32.3.1.(1) |
| CSA | CAN/CSA‐F379.1‐88 | Solar Domestic Hot Water Systems (Liquid to Liquid Heat Transfer) | 7.2.10.13.(1) |
| CSA | CAN/CSA‐F383‐87 | Installation Code for Solar Domestic Hot Water Systems | 7.6.1.8.(1) |
| CSA | CAN/CSA‐G30.18‐M92 | Billet‐Steel Bars for Concrete Reinforcement | 9.3.1.1.(4) |
| CSA | CAN/CSA‐G40.21‐04 | Structural Quality Steel | 4.2.3.8.(1) Table 5.10.1.1. 9.23.4.3.(2) |
| CSA | G401‐01 | Corrugated Steel Pipe Products | Table 5.10.1.1. 7.2.6.8.(1) 9.14.3.1.(1) |
| CSA | O80 Series‐97 | Wood Preservation | 3.1.4.4.(1) 4.2.3.2.(1) 4.2.3.2.(2) Table 5.10.1.1. |
| CSA | O80.1‐97 | Preservative Treatment of All Timber Products by Pressure Processes | Table 5.10.1.1. 9.3.2.9.(5) |
| CSA | O80.2‐97 | Preservative Treatment of Lumber, Timber, Bridge Ties, and Mine Ties by Pressure Processes | 4.2.3.2.(1) Table 5.10.1.1. 9.3.2.9.(5) |
| CSA | O80.3‐97 | Preservative Treatment of Piles by Pressure Processes | 4.2.3.2.(1) |
| CSA | O80.9‐97 | Preservative Treatment of Plywood by Pressure Processes | Table 5.10.1.1. 9.3.2.9.(5) |
| CSA | O80.15‐97 | Preservative Treatment of Wood for Building Foundation Systems, Basements, and Crawl Spaces by Pressure Processes | 4.2.3.2.(1) Table 5.10.1.1. 9.3.2.9.(5) |
| CSA | O80.34‐97 | Pressure Preservative Treatment of Lumber and Timbers with Borates for Use Out of Ground Contact and Continuously Protected from Liquid Water | Table 5.10.1.1. 9.3.2.9.(5) 9.3.2.9.(6) |
| CSA | CAN/CSA‐O86‐01 (Including Supplement CAN/CSA‐O86S1‐05) | Engineering Design in Wood | Table 4.1.8.9. 4.3.1.1.(1) |
| CSA | O115‐M1982 | Hardwood and Decorative Plywood | Table 5.10.1.1. 9.27.9.1.(1) 9.30.2.2.(1) |
| CSA | O118.1‐97 | Western Cedars Shakes and Shingles | Table 5.10.1.1. 9.26.2.1.(1) 9.27.7.1.(1) |
| CSA | O118.2‐M1981 | Eastern White Cedar Shingles | Table 5.10.1.1. 9.26.2.1.(1) 9.27.7.1.(1) |
| CSA | O121‐M1978 | Douglas Fir Plywood | Table 5.10.1.1. 9.23.14.2.(1) 9.23.15.2.(1) Table 9.23.16.2.A. 9.27.9.1.(1) 9.30.2.2.(1) Table A‐13 Table A‐14 Table A‐15 |
| CSA | CAN/CSA‐O122‐M89 | Structural Glued‐Laminated Timber | Table A‐11 Table A‐16 |
| CSA | CAN/CSA‐O132.2 Series‐90 | Wood Flush Doors | Table 5.10.1.1. 9.6.5.1.(1) |
| CSA | CAN/CSA‐O141‐05 | Softwood Lumber | Table 5.10.1.1. 9.3.2.6.(1) |
| CSA | O151‐04 | Canadian Softwood Plywood | Table 5.10.1.1. 9.23.14.2.(1) 9.23.15.2.(1) Table 9.23.16.2.A. 9.27.9.1.(1) 9.30.2.2.(1) Table A‐13 Table A‐14 Table A‐15 |
| CSA | O153‐M1980 | Poplar Plywood | Table 5.10.1.1. 9.23.14.2.(1) 9.23.15.2.(1) Table 9.23.16.2.A. 9.27.9.1.(1) 9.30.2.2.(1) |
| CSA | CAN/CSA‐O177‐M89 | Qualification Code for Manufacturers of Structural Glued‐Laminated Timber | 4.3.1.2.(1) Table A‐11 Table A‐16 |
| CSA | CAN/CSA‐O325.0‐92 | Construction Sheathing | Table 5.10.1.1. 9.23.14.2.(1) 9.23.14.4.(2) Table 9.23.14.5.B. 9.23.15.2.(1) 9.23.15.3.(2) Table 9.23.15.7.B. Table 9.23.16.2.B. 9.29.9.1.(2) 9.29.9.2.(5) Table A‐13 Table A‐14 Table A‐15 |
| CSA | O437.0‐93 | OSB and Waferboard | Table 5.10.1.1. 9.23.14.2.(1) 9.23.14.4.(2) 9.23.15.2.(1) 9.23.15.3.(2) Table 9.23.16.2.A. 9.27.11.1.(1) 9.29.9.1.(2) 9.30.2.2.(1) Table A‐13 Table A‐14 Table A‐15 |
| CSA | CAN/CSA‐S16‐01 (Including Supplement CAN/CSA‐S16S1‐05) | Limit States Design of Steel Structures | Table 4.1.8.9. 4.3.4.1.(1) |
| CSA | CAN/CSA‐S136‐01 (Including Supplement CAN/CSA‐S136S1‐04) | North American Specification for the Design of Cold‐Formed Steel Structural Members (using the Appendix B provisions applicable to Canada) | 4.3.4.2.(1) |
| CSA | CAN3‐S157‐M83 | Strength Design in Aluminum | 4.3.5.1.(1) |
| CSA | S269.1‐1975 | Falsework for Construction Purposes | 4.1.1.3.(4) |
| CSA | CAN/CSA‐S269.2‐M87 | Access Scaffolding for Construction Purposes | 4.1.1.3.(4) |
| CSA | CAN/CSA‐S269.3‐M92 | Concrete Formwork | 4.1.1.3.(4) |
| CSA | S304.1‐04 | Design of Masonry Structures | Table 4.1.8.9. 4.3.2.1.(1) |
| CSA | S307‐M1980 | Load Test Procedure for Wood Roof Trusses for Houses and Small Buildings | 9.23.13.11.(5) |
| CSA | S350‐M1980 | Code of Practice for Safety in Demolition of Structures | 8.1.1.3.(1) |
| CSA | CAN3‐S367‐M81 | Air‐Supported Structures | 4.4.1.1.(1) |
| CSA | CAN/CSA‐S406‐92 | Construction of Preserved Wood Foundations | 9.15.2.4.(1) 9.16.5.1.(1) |
| CSA | CAN/CSA‐S413‐94 | Parking Structures | 4.4.2.1.(1) |
| CSA | CAN/CSA‐Z32‐04 | Electrical Safety and Essential Electrical Systems in Health Care Facilities | 3.2.7.3.(4) 3.2.7.6.(1) |
| CSA | CAN/CSA‐Z240 MH Series | Mobile Homes | 1.1.1.1.(1) |
| CSA | CAN/CSA‐Z240.2.1‐92 | Structural Requirements for Mobile Homes | 9.12.2.2.(6) 9.15.1.3.(1) |
| CSA | Z240.10.1‐94 | Site Preparation, Foundation, and Anchorage of Mobile Homes | 9.15.1.3.(1) 9.23.6.3.(1) |
| CSA | CAN/CSA‐Z305.1‐92 | Nonflammable Medical Gas Piping Systems | 3.7.3.1.(1) |
| CSA | CAN/CSA‐Z317.2‐01 | Special Requirements for Heating, Ventilation, and Air Conditioning (HVAC) Systems in Health Care Facilities | 6.2.1.1.(1) |
| CWC | 2004 | Engineering Guide for Wood Frame Construction | 9.4.1.1.(1) |
| EPA | EPA 402‐R‐93‐003 | Protocols for Radon and Radon Decay Product Measurements in Homes | 9.13.4.6.(6) |
| HC | H46‐2/90‐156E | Exposure Guidelines for Residential Indoor Air Quality | 9.13.4.6.(9) |
| ISO | 8201:1987(E) | Acoustics ‐ Audible emergency evacuation signal | 3.2.4.18.(2) |
| NFPA | 13‐1999 | Installation of Sprinkler Systems | 3.2.4.8.(2) 3.2.4.15.(1) 3.2.5.13.(1) 3.3.2.13.(3) |
| NFPA | 13D‐2002 | Installation of Sprinkler Systems in One‐ and Two‐Family Dwellings and Manufactured Homes | 3.2.5.13.(3) |
| NFPA | 13R‐2002 | Installation of Sprinkler Systems in Residential Occupancies up to and Including Four Stories in Height | 3.2.5.13.(2) |
| NFPA | 14‐2003 | Installation of Standpipe and Hose Systems | 3.2.5.9.(1) 3.2.5.10.(1) |
| NFPA | 20‐2003 | Installation of Stationary Pumps for Fire Protection | 3.2.5.19.(1) |
| NFPA | 80‐1999 | Fire Doors and Fire Windows | 3.1.8.5.(2) 3.1.8.10.(2) 3.1.8.12.(2) 3.1.8.12.(3) 3.1.8.14.(1) 9.10.13.1.(1) |
| NFPA | 82‐2004 | Incinerators and Waste and Linen Handling Systems and Equipment | 6.2.6.1.(1) 9.10.10.5.(2) |
| NFPA | 96‐2001 | Ventilation Control and Fire Protection of Commercial Cooking Operations | 6.2.2.6.(1) |
| NFPA | 211‐2003 | Chimneys, Fireplaces, Vents, and Solid Fuel‐Burning Appliances | 6.3.1.2.(2) 6.3.1.3.(1) |
| NFPA | 214‐2005 | Water‐Cooling Towers | 6.2.3.14.(3) |
| NLGA | 2004 | Standard Grading Rules for Canadian Lumber (Interpretation Included) | 9.3.2.1.(1) |
| SMACNA | 1995 | HVAC Duct Construction Standards ‐ Metal and Flexible 2nd Edition | 9.33.6.5.(2) |
| TC | Canadian Aviation Regulations ‐ Part III | 4.1.5.14.(1) | |
| TPIC | 1996 | Truss Design Procedures and Specifications for Light Metal Plate Connected Wood Trusses | 9.23.13.11.(6) |
| UL | UL‐300 | Fire Extinguishing Systems for Protection of Restaurant Cooking Areas | 6.2.2.6.(2) |
| ULC | CAN/ULC‐S101‐04 | Fire Endurance Tests of Building Construction and Materials | 3.1.5.12.(3) 3.1.5.12.(4) 3.1.5.12.(6) 3.1.7.1.(1) 3.1.11.7.(1) 3.2.3.8.(1) 3.2.6.5.(6) |
| ULC | CAN/ULC‐S102‐03 | Test for Surface Burning Characteristics of Building Materials and Assemblies | 3.1.5.21.(1) 3.1.12.1.(1) |
| ULC | CAN/ULC‐S102.2‐03 | Test for Surface Burning Characteristics of Flooring, Floor Coverings, and Miscellaneous Materials and Assemblies | 3.1.12.1.(2) 3.1.13.4.(1) |
| ULC | ULC‐S102.3‐M82 | Fire Test of Light Diffusers and Lenses | 3.1.13.4.(1) |
| ULC | CAN4‐S104‐M80 | Fire Tests of Door Assemblies | 3.1.8.4.(1) 3.2.6.5.(3) |
| ULC | CAN4‐S105‐M85 | Fire Door Frames Meeting the Performance Required by CAN4‐S104 | 9.10.13.6.(1) |
| ULC | CAN4‐S106‐M80 | Fire Tests of Window and Glass Block Assemblies | 3.1.8.4.(1) |
| ULC | CAN/ULC‐S107‐03 | Fire Tests of Roof Coverings | 3.1.15.1.(1) |
| ULC | CAN/ULC‐S109‐03 | Flame Tests of Flame‐Resistant Fabrics and Films | 3.1.6.5.(1) 3.1.16.1.(1) 3.6.5.2.(2) 3.6.5.3.(1) 9.33.6.3.(1) |
| ULC | CAN/ULC‐S110‐M86 | Test for Air Ducts | 3.6.5.1.(2) 3.6.5.1.(5) 9.33.6.2.(2) 9.33.6.2.(4) |
| ULC | ULC‐S111‐95 | Fire Tests for Air Filter Units | 6.2.3.13.(1) 9.33.6.15.(1) |
| ULC | CAN/ULC‐S112‐M90 | Fire Test of Fire‐Damper Assemblies | 3.1.8.4.(1) |
| ULC | CAN/ULC‐S112.1‐M90 | Leakage Rated Dampers for Use in Smoke Control Systems | 6.2.3.9.(3) |
| ULC | CAN4‐S113‐79 | Wood Core Doors Meeting the Performance Required by CAN4‐S104‐77 for Twenty Minute Fire Rated Closure Assemblies | 9.10.13.2.(1) |
| ULC | ULC‐S115‐95 | Fire Tests of Firestop Systems | 3.1.5.16.(3) 3.1.9.1.(1) 3.1.9.1.(2) 3.1.9.4.(4) 9.10.9.7.(3) |
| ULC | CAN4‐S124‐M85 | Test for the Evaluation of Protective Coverings for Foamed Plastic | 3.1.5.12.(2) |
| ULC | CAN/ULC‐S126‐M86 | Test for Fire Spread Under Roof‐Deck Assemblies | 3.1.14.1.(1) 3.1.14.2.(1) |
| ULC | CAN/ULC‐S134‐92 | Fire Test of Exterior Wall Assemblies | 3.1.5.5.(1) 3.2.2.45.(3) |
| ULC | ULC‐S135‐04 | Test Method for the Determination of Combustibility Parameters of Building Materials Using an Oxygen Consumption Calorimeter (Cone Calorimeter) | 3.1.5.1.(2) |
| ULC | S505‐1974 | Fusible Links for Fire Protection Service | 3.1.8.9.(1) |
| ULC | CAN/ULC‐S524‐01 | Installation of Fire Alarm Systems | 3.2.4.5.(1) |
| ULC | CAN/ULC‐S531‐02 | Smoke Alarms | 3.2.4.20.(1) 9.10.19.1.(1) |
| ULC | CAN/ULC‐S537‐04 | Verification of Fire Alarm Systems | 3.2.4.5.(2) |
| ULC | CAN/ULC‐S553‐02 | Installation of Smoke Alarms | 3.2.4.20.(7) |
| ULC | CAN/ULC‐S561‐03 | Installation and Services for Fire Signal Receiving Centres and Systems | 3.2.4.7.(4) |
| ULC | CAN/ULC‐S610‐M87 | Factory‐Built Fireplaces | 9.22.8.1.(1) |
| ULC | ULC‐S628‐93 | Fireplace Inserts | 9.22.10.1.(1) |
| ULC | CAN/ULC‐S629‐M87 | 650°C Factory‐Built Chimneys | 9.33.10.2.(1) |
| ULC | CAN/ULC‐S639‐M87 | Steel Liner Assemblies for Solid‐Fuel Burning Masonry Fireplaces | 9.22.2.3.(1) |
| ULC | CAN/ULC‐S701‐01 | Thermal Insulation, Polystyrene, Boards and Pipe Covering | Table 5.10.1.1. 9.15.4.1.(1) Table 9.23.16.2.A. 9.25.2.2.(1) |
| ULC | CAN/ULC‐S702‐97 | Mineral Fibre Thermal Insulation for Buildings | Table 5.10.1.1. Table 9.23.16.2.A. 9.25.2.2.(1) |
| ULC | CAN/ULC‐S703‐01 | Cellulose Fibre Insulation (CFI) for Buildings | Table 5.10.1.1. 9.25.2.2.(1) |
| ULC | CAN/ULC‐S704‐03 | Thermal Insulation, Polyurethane and Polyisocyanurate, Boards, Faced | Table 5.10.1.1. Table 9.23.16.2.A. 9.25.2.2.(1) |
| ULC | CAN/ULC‐S705.1‐01 | Thermal Insulation ‐ Spray Applied Rigid Polyurethane Foam, Medium Density ‐ Material ‐ Specification | Table 5.10.1.1. 9.25.2.2.(1) |
| ULC | CAN/ULC‐S705.2‐98 | Thermal Insulation ‐ Spray‐Applied Rigid Polyurethane Foam, Medium Density, Installer's Responsibilities ‐ Specification | 5.3.1.3.(3) Table 5.10.1.1. 9.25.2.5.(1) |
| ULC | CAN/ULC‐S706‐02 | Wood Fibre Thermal Insulation for Buildings | Table 5.10.1.1. 9.23.15.7.(3) Table 9.23.16.2.A. 9.25.2.2.(1) 9.29.8.1.(1) |
| ULC | ULC/ORD‐C199P‐2002 | Combustible Piping for Sprinkler Systems | 3.2.5.14.(2) 3.2.5.14.(5) |
| ULC | ULC/ORD‐C376‐1995 | Fire Growth of Foamed Plastic Insulated Building Panels in a Full‐Scale Room Configuration | 3.1.5.12.(7) |
| ULC | ULC/ORD‐C1254.6‐1995 | Fire Testing of Restaurant Cooking Area Fire Extinguishing System Units | 6.2.2.6.(2) |
[Rev. 2, B.C. Reg. 73/2008.]
[Rev. 4, B.C. Reg. 1/1009.]
[Rev. 12, B.C. Reg. 336/2010.]
1) The abbreviations of proper names in this Code shall have the meanings assigned to them in this Article (the appropriate addresses of the organizations are shown in brackets).
| ACGIH | ..... | American Conference of Governmental Industrial Hygienists (1330 Kemper Meadow Drive, Cincinnati, Ohio 45240‐1634 U.S.A.; www.acgih.org) |
| ANSI | ..... | American National Standards Institute (25 West 43rd Street, 4th Floor, New York, New York 10036 U.S.A.; www.ansi.org) |
| ASCE | ..... | American Society of Civil Engineers (1801 Alexander Bell Drive, Reston, Virginia 20191‐4400 U.S.A.; www.asce.org) |
| ASHRAE | ..... | American Society of Heating, Refrigerating and Air‐Conditioning Engineers (1791 Tullie Circle, N.E., Atlanta, Georgia 30329‐2305 U.S.A.; www.ashrae.org) |
| ASME | ..... | American Society of Mechanical Engineers (22 Law Drive, P.O. Box 2900, Fairfield, New Jersey 07007‐2900 U.S.A.; www.asme.org) |
| ASPE | ..... | American Society of Plumbing Engineers (8614 Catalpa Avenue, Suite 1007, Chicago, Illinois 60656‐1116 U.S.A.; www.aspe.org) |
| ASSE | ..... | American Society of Sanitary Engineering (A‐901 Canterbury Road, West Lake, Ohio 44145 U.S.A.; www.asse‐plumbing.org) |
| ASTM | ..... | American Society for Testing and Materials International (100 Barr Harbor Drive, West Conshohocken, Pennsylvania 19428‐2959 U.S.A.; www.astm.org) |
| AWPA | ..... | American Wood‐Preservers' Association (P.O. Box 388, Selma, Alabama 36702‐0388 U.S.A.; www.awpa.com) |
| AWWA | ..... | American Water Works Association (6666 West Quincy Avenue, Denver, Colorado 80235 U.S.A.; www.awwa.org) |
| BIA | ..... | Brick Industry Association (11490 Commerce Park Drive, Reston, Virginia 20191‐1525 U.S.A.; www.bia.org) |
| BNQ | ..... | Bureau de normalisation du Québec (333, rue Franquet, Sainte‐Foy, Québec G1P 4C7; www.bnq.qc.ca) |
| CAN | ..... | National Standard of Canada designation. (The number or name following the CAN designation
represents the agency under whose auspices the standard is issued. CAN1 designates CGA, CAN2 designates CGSB, CAN3 designates CSA, and CAN4 designates ULC.) |
| CCBFC | ..... | Canadian Commission on Building and Fire Codes (National Research Council of Canada, Ottawa, Ontario K1A 0R6; www.nationalcodes.ca) |
| CGSB | ..... | Canadian General Standards Board (Place du Portage III, 6B111 Laurier Street, Gatineau, Quebec K1A 1G6; www.pwgsc.gc.ca/cgsb) |
| CMHC | ..... | Canada Mortgage and Housing Corporation (700 Montreal Road, Ottawa, Ontario K1A 0P7; www.cmhc.ca) |
| CRCA | ..... | Canadian Roofing Contractors' Association (2430 Don Reid Drive, Suite 100, Ottawa, Ontario K1H 1E1; www.roofingcanada.com) |
| CSA | ..... | Canadian Standards Association (5060 Spectrum Way, Suite 100, Mississauga, Ontario L4W 5N6; www.csa.ca) |
| CWC | ..... | Canadian Wood Council (99 Bank Street, Suite 400, Ottawa, Ontario K1P 6B9; www.cwc.ca) |
| EPA | ..... | Environmental Protection Agency (Office of Radiation and Indoor Air, 1200 Pennsylvania Avenue, NW, 6609G, Washington, D.C. 20460 U.S.A.; www.epa.gov) |
| FCC | ..... | Forintek Canada Corporation (319, rue Franquet, Sainte‐Foy, Québec G1P 4R4; www.forintek.ca) |
| FM Global | ..... | FM Global (1151 Boston‐Providence Turnpike, P.O. Box 9102, Norwood, Massachusetts 02062 U.S.A.; www.fmglobal.com) |
| HC | ..... | Health Canada (Communications Directorate, Ottawa, Ontario K1A 0K9; www.hc‐sc.gc.ca) |
| HI | ..... | Hydronics Institute (35 Russo Place, Berkley Heights, New Jersey 07922 U.S.A.; www.gamanet.org) |
| HRAI | ..... | Heating, Refrigeration and Air Conditioning Institute of Canada (5045 Orbitor Drive, Building 11, Suite 300, Mississauga, Ontario L4W 4Y4; www.hrai.ca) |
| HVI | ..... | Home Ventilating Institute (1000 N. Rand Road, Suite 214, Wauconda, Illinois 60084 U.S.A.; www.hvi.org) |
| IRC | ..... | Institute for Research in Construction (National Research Council of Canada, Ottawa, Ontario K1A 0R6; irc.nrc‐cnrc.gc.ca) |
| ISO | ..... | International Organization for Standardization (Standards Council of Canada, 270 Albert Street, Suite 200, Ottawa, Ontario K1P 6N7; www.iso.org) |
| MSC | ..... | Meteorological Service of Canada [formerly AES ‐ Atmospheric Environment Service] (Environment Canada, 4905 Dufferin Street, Toronto, Ontario M3H 5T4; www.msc‐smc.ec.gc.ca) |
| NBC | ..... | National Building Code of Canada 2005 (see CCBFC) |
| NCMA | ..... | National Concrete Masonry Association (13750 Sunrise Valley Drive, Herndon, Virginia 20171‐4662 U.S.A.; www.ncma.org) |
| NFPA | ..... | National Fire Protection Association (1 Batterymarch Park, Quincy, Massachusetts 02169‐7471 U.S.A.; www.nfpa.org) |
| NIST | ..... | National Institute of Standards and Technology (100 Bureau Drive, Stop 1070, Gaithersburg, Maryland 20899‐1070 U.S.A.; www.nist.gov) |
| NLGA | ..... | National Lumber Grades Authority (406 ‐ First Capital Place, 960 Quayside Drive, New Westminster, British Columbia V3M 6G2; www.nlga.org) |
| NRC | ..... | National Research Council of Canada (Ottawa, Ontario K1A 0R6; www.nrc‐cnrc.gc.ca) |
| NRCA | ..... | National Roofing Contractors Association (10255 W. Higgins Road, Suite 600, Rosemont, Illinois 60018‐5607 U.S.A.; www.nrca.net) |
| NYCDH | ..... | New York City Department of Health and Mental Hygiene (Environmental and Occupational Disease Epidemiology, 253 Broadway, Suite 402, CN‐34C, New York, New York 10007‐2333 U.S.A.; www.nyc.gov/html/doh) |
| OMMAH | ..... | Ontario Ministry of Municipal Affairs and Housing (777 Bay Street, 2nd Floor, Toronto, Ontario M5G 2E5; www.obc.mah.gov.on.ca) |
| ONHWP | ..... | Ontario New Home Warranty Program (now Tarion Warranty Corporation, 5150 Yonge Street, Concourse Level, Toronto, Ontario M2N 6L8; www.tarion.com) |
| SFPE | ..... | Society of Fire Protection Engineers (7315 Wisconsin Avenue, Suite 620E, Bethesda, Maryland 20814 U.S.A.; www.sfpe.org) |
| SMACNA | ..... | Sheet Metal and Air Conditioning Contractors' National Association (4201 Lafayette Center Drive, Chantilly, Virginia 20151‐1209 U.S.A.; www.smacna.org) |
| TC | ..... | Transport Canada (Public Affairs, Tower C, Place de Ville, 330 Sparks Street, Area B, 19th Floor, Ottawa, Ontario K1A 0N5; www.tc.gc.ca) |
| TECA | ..... | Thermal Environmental Comfort Association (6004 Lois Street, Powell River, British Columbia V8A 4T7; www.teca.ca) |
| TPIC | ..... | Truss Plate Institute of Canada (℅ 16 Nixon Road, Bolton, Ontario L7E 1K3, Attn: Ken Coo; www.tpic.ca) |
| UL | ..... | Underwriters Laboratories Inc. (333 Pfingsten Road, Northbrook, Illinois 60062‐2096 U.S.A.; www.ul.com) |
| ULC | ..... | Underwriters' Laboratories of Canada (7 Underwriters Road, Toronto, Ontario M1R 3B4; www.ulc.ca) |
| WCLIB | ..... | West Coast Lumber Inspection Bureau (P.O. Box 23145, Portland, Oregon 97281 U.S.A.; www.wclib.org) |
| WWPA | ..... | Western Wood Products Association (522 SW Fifth Avenue, Suite 500, Portland, Oregon 97204‐2122 U.S.A.; www.wwpa.org) |