Appendix A — Division B

Explanatory Material

A-1.1.2.1.(1) Objectives and Functional Statements Attributed to Acceptable Solutions
The objectives and functional statements attributed to each Code provision are shown in Tables at the end of each Part in Division B.
Many provisions in Division B serve as modifiers of or pointers to other provisions, or serve other clarification or explanatory purposes. In most cases, no objectives and functional statements have been attributed to such provisions, which therefore do not appear in the above-mentioned tables.
For provisions that serve as modifiers of or pointers to other referenced provisions and that do not have any objectives and functional statements attributed to them, the objectives and functional statements that should be used are those attributed to the provisions they reference.
A-1.1.3.1.(1) Climatic and Seismic Values
Climatic values for municipalities not listed in Appendix C may be obtained by writing to the Meteorological Service of Canada, Environment Canada, 4905 Dufferin Street, Toronto, Ontario M3H 5T4.
Seismic values for municipalities not listed in Appendix C may be obtained through the Natural Resources Canada Web site at www.EarthquakesCanada.ca, or by writing to the Geological Survey of Canada at 7 Observatory Crescent, Ottawa, Ontario K1A 0Y3, or at P.O. Box 6000, Sidney, B.C. V8L 4B2.
A-1.1.3.1.(2) Winter Design Temperatures
The 2.5% values referred to in Sentence 1.1.3.1.(2) are the least restrictive temperatures that can be used. A designer may choose to use the 1% values given in Appendix C, which are in excess of the Code minimums but are considered acceptable.
A-1.3.1.2.(1) Applicable Editions
Where documents are referenced in Appendices A, B and C of this Code, they shall be the editions designated in Table A-1.3.1.2.(1)
Table A-1.3.1.2.(1)
Documents Referenced in Appendices A, B and C of Book I (General) of the British Columbia Building Code 2012
Forming part of Appendix Note A-1.3.1.2.(1)
Issuing Agency Document Number(1) Title of Document(2) Code Reference
ASCE SEI/ASCE 8-02 Design of Cold-Formed Stainless Steel Structural Members A-4.3.4.2.(1)
ANSI/
ASHRAE 		62-2001 Ventilation for Acceptable Indoor Air Quality (except Addendum n) A-9.25.5.2.
ANSI/UL 199 Standard for Safety of Automatic Sprinklers for Fire-Protection Service A-3.2.5.12.(8)
ANSI/UL 1626 Standard for Safety of Residential Sprinklers for Fire-Protection Service A-3.2.5.12.(8)
change beginASHRAE 2009 ASHRAE Handbook - Fundamentals A-9.36.2.4.(1)
A-9.36.2.4.(1)D.change end
ASME B18.6.1-1981 Wood Screws (Inch Series) change begin9.23.3.1.(3)change end
change beginASME/CSA ASME A17.1-2010/CSA B44-10 Safety Code for Elevators and Escalators A-3.5.2.1.(1)change end
ASTM A 390-06 Zinc-Coated (Galvanized) Steel Poultry Fence Fabric (Hexagonal and Straight Line) Table A-9.10.3.1.B
ASTM C 516-08 Vermiculite Loose Fill Thermal Insulation A-9.25.2.4.(5)
change beginASTM C 1193-11a Use of Joint Sealants A-Table 5.10.1.1.
A-9.27.4.2.(1)change end
ASTM C 1299-03 Selection of Liquid-Applied Sealants A-Table 5.10.1.1.
A-9.27.4.2.(1)
change beginASTM C 1472-10 Calculating Movement and Other Effects When Establishing Sealant Joint Width A-Table 5.10.1.1.
A-9.27.4.2.(1)change end
ASTM D 1037-06a Evaluating Properties of Wood-Base Fiber and Particle Panel Materials A-9.23.15.2.(4)
ASTM D 1143/D 1143M-07e1 Deep Foundations Under Static Axial Compressive Load A-4.2.7.2.(2)
ASTM E 336-05 Measurement of Airborne Sound Attenuation between Rooms in Buildings A-9.11.1.1.(1)
ASTM E 492-09 Laboratory Measurement of Impact Sound Transmission Through Floor-Ceiling Assemblies Using The Tapping Machine A-9.11.1.1.(1)
ASTM E 597-95 Determining a Single Number Rating of Airborne Sound Insulation for Use in Multi-Unit Building Specifications A-9.11.1.1.(1)
ASTM E 736-00 Cohesion/Adhesion of Sprayed Fire-Resistive Materials Applied to Structural Members Table A-9.10.3.1.B
change beginASTM E 1007-11e1 Field Measurement of Tapping Machine Impact Sound Transmission Through Floor-Ceiling Assemblies and Associated Support Structures A-9.11.1.1.(1)change end
change beginASME E 2357-11 Determining Air Leakage of Air Barrier Assemblies A-9.36.2.9.(1)change end
ASTM F 476-84 Security of Swinging Door Assemblies A-9.7.5.2.(2)
BC   Book II (Plumbing Systems) of the British Columbia Building Code 2012 A-2.2.1.1.(1)(3)
A-3.2.1.1.(1)(3)
A-4.1.6.4.(3)
A-9.36.5.8.(5)
Appendix C
BC B.C. Reg. 100/2004 Electrical Safety Regulation A-3.2.4.21.(6)(a)
A-9.34.2.
A-9.35.2.2.(1)
BC B.C. Reg. 101/2004 Elevating Devices Safety Regulation A-3.5.2.1.(1)
change beginBC S.B.C. 1998, c. 43 Strata Property Act A-9.37.1.1.change end
CCBFC NRCC 35951 Guidelines for Application of Part 3 of the National Building Code of Canada to Existing Buildings A-1.1.1.2.(1)(3)
change beginCCBFC NRCC 38730 Model National Energy Code of Canada for Houses 1997 A-9.36.3.10.(1)
A-9.36.4.2.(1)change end
CCBFC NRCC 38732 National Farm Building Code of Canada 1995 A-1.4.1.2.(1)(3)
A-Table 4.1.2.1.
A-5.1.2.1.(1)
CCBFC NRCC 40383 User's Guide – NBC 1995, Fire Protection, Occupant Safety and Accessibility (Part 3) A-1.1.1.2.(1)(3)
CCBFC NRCC 43963 User's Guide – NBC 1995, Application of Part 9 to Existing Buildings A-1.1.1.2.(1)(3)
CCBFC NRCC 48192 User's Guide – NBC 2005, Structural Commentaries (Part 4 of Division B) A-1.1.1.2.(1)
A-4.1.1.3.(1)
A-4.1.1.3.(2)
A-3.2.5.12.(8)
A-4.1.3.4.(1)
A-4.1.3.5.(1)
A-4.1.3.5.(3)
A-Table 4.1.8.5.
A-Table 4.1.8.6.
A-5.1.4.2.
Appendix C
CCBFC NRCC 53303 National Fire Code of Canada 2010 A-1.1.1.2.(1)(3)
A-2.2.1.1.(1)(3)
A-3.1.2.3.(1)
A-3.2.1.1.(1)(3)
A-3.2.4.7.(2)
A-3.2.7.8.(3)
A-3.3.
A-3.3.1.2.(1)
A-3.3.1.7.(1)
A-3.3.3.1.(1)
A-3.3.6.1.(1)
B-3.2.6.
CCBFC NRCC 53543 User's Guide – NBC 2010, Structural Commentaries (Part 4 of Division B) A-1.1.1.2.(1)(3)
A-4.1.1.3.(1)
A-4.1.1.3.(2)
A-4.1.2.1.
A-4.1.2.1.(1)
A-4.1.3.
A-4.1.3.2.(2)
A-4.1.3.2.(4)
A-4.1.3.2.(5)
A-4.1.3.3.(2)
A-4.1.3.4.(1)
A-4.1.3.5.(1)
A-4.1.3.5.(3)
A-4.1.3.6.(1)
A-4.1.3.6.(2)
A-4.1.3.6.(3)
A-4.1.5.8.
A-4.1.5.17.
A-4.1.6.2.
A-4.1.6.2.(4)(b)
A-4.1.6.3.(2)
A-4.1.6.4.(1)
A-4.1.7.1.(1) to (3)
A-4.1.7.1.(5)(a) to (c)
A-4.1.7.1.(5)(d)
A-4.1.7.1.(6)(a)
A-4.1.7.1.(6)(c)
A-4.1.7.1.(6)(d) and 4.1.7.2.(1)(b)
A-4.1.7.2.(1) and (2)
A-4.1.7.3.(1)
A-4.1.8.2.(1)
A-4.1.8.3.(4)
A-4.1.8.3.(6)
A-4.1.8.3.(7)(b) and (c)
A-4.1.8.3.(8)
A-4.1.8.4.(3) and Table 4.1.8.4.A.
A-Table 4.1.8.5.
A-Table 4.1.8.6.
A-4.1.8.7.(1)
A-4.1.8.9.(4)
A-4.1.8.9.(5)
A-4.1.8.11.(3)
A-4.1.8.12.(1)(a)
A-4.1.8.12.(1)(b)
A-4.1.8.12.(3)
A-4.1.8.12.(4)(a)
A-4.1.8.13.(4)
A-4.1.8.15.(1)
A-4.1.8.15.(3)
A-4.1.8.15.(4)
A-4.1.8.15.(5)
A-4.1.8.15.(6)
A-4.1.8.15.(7)
A-4.1.8.16.(1)
A-4.1.8.16.(3)(a)
A-4.1.8.16.(4)
A-4.1.8.16.(5)(a)
A-4.1.8.16.(7)
A-4.1.8.17.(1)
A-4.1.8.18.
A-4.2.4.1.(3)
A-4.2.4.1.(5)
A-4.2.5.1.(1)
A-4.2.6.1.(1)
A-4.2.7.2.(1)
A-5.1.4.2.
Appendix C
change beginCCBFC NRCC 54435 National Energy Code of Canada for Buildings 2011 A-9.36.1.3.
A-9.36.2.4.(1)
A-9.36.3.10.(1)
A-9.36.4.2.(1)
A-9.36.5.2.change end
CGSB CAN/CGSB-7.2-94 Adjustable Steel Columns A-9.17.3.4.
CGSB CAN/CGSB-12.20-M89 Structural Design of Glass for Buildings A-9.6.1.3.(1)
CGSB CAN/CGSB-71.26-M88 Adhesive for Field-Gluing Plywood to Lumber Framing for Floor Systems Table A-9.23.4.2.(2)C
CGSB CAN/CGSB-82.6-M86 Doors, Mirrored Glass, Sliding or Folding, Wardrobe A-9.6.1.2.(2)
CGSB CAN/CGSB-93.1-M85 Sheet, Aluminum Alloy, Prefinished, Residential A-9.27.11.1.(3) and (4)
CGSB CAN/CGSB-93.2-M91 Prefinished Aluminum Siding, Soffits, and Fascia, for Residential Use A-9.27.11.1.(3) and (4)
change beginCGSB CAN/CGSB-149.10-M86 Determination of the Airtightness of Building Envelopes by the Fan Depressurization Method A-9.36.5.10.(11)change end
CISC 2009 Crane-Supporting Steel Structures: Design Guide A-4.1.3.2.(2)
CMHC 1993 Testing of Fresh Air Mixing Devices A-9.32.3.4.
CMHC 1988 Air Permeance of Building Materials A-5.4.1.2.(1) and (2)
Table A-9.25.5.1.(1)
CMHC/HC 2007 Radon: A Guide for Canadian Homeowners A-5.4.1.1.
A-6.2.1.1.
A-9.13.4.3.
CSA CAN/CSA-A23.3-04 Design of Concrete Structures A-4.1.3.2.(4)
A-4.3.3.1.(1)
change beginCSA A23.4-09 Precast Concrete – Materials and Construction A-4.3.3.1.(1)change end
CSA A82.31-M1980 Gypsum Board Application Table A-9.10.3.1.A
Table A-9.10.3.1.B
CSA CAN/CSA-A370-04 Connectors for Masonry A-9.21.4.5.(2)
CSA AAMA/WDMA/CSA 101/I.S.2/A440-08 NAFS – North American Fenestration Standard/Specification for Windows, Doors, and Skylights A-5.3.1.2.
A-9.7.4.2.(1)
CSA A440S1-09 Canadian Supplement to AAMA/WDMA/CSA 101/I.S.2/A440, NAFS – North American Fenestration Standard/Specification for Windows, Doors, and Skylightschange begin, as updated by Update No. 1 (July 2013)change end A-5.10.2.2.
A-9.7.4.2.(1)
change beginCSA A440.2-09/A440.3-09 Fenestration Energy Performance/User Guide to CSA A440.2-09, Fenestration Energy Performance A-Table 9.36.2.7.A.change end
CSA B111-1974 Wire Nails, Spikes and Staples A-Table 9.23.3.5.B.
change beginCSA CAN/CSA-B214-07 Installation Code for Hydronic Heating Systems A-9.36.3.4.(1)change end
CSA CAN/CSA-B365-01 Installation Code for Solid-Fuel-Burning Appliances and Equipment A-9.33.5.3.
change beginCSA CAN/CSA-C439-09 Rating the Performance of Heat/Energy-Recovery Ventilators A-9.36.3.9.(3)change end
change beginCSA F280-12 Determining the Required Capacity of Residential Space Heating and Cooling Appliances A-9.36.3.2.(1)
A-9.36.5.15.(5)change end
CSA CAN/CSA-F326-M91 Residential Mechanical Ventilation Systems A-9.32.3.
A-9.32.3.1.(1)
A-9.32.3.5.
A-9.32.3.7.
A-9.32.3.8.
A-9.33.6.13.
CSA O86-09 Engineering Design in Wood A-9.15.2.4.(1)
A-9.23.4.2.
change beginCSA O112.9-10 Evaluation of Adhesives for Structural Wood Products (Exterior Exposure) Table A-9.10.3.1.Bchange end
change beginCSA O112.10-08 Evaluation of Adhesives for Structural Wood Products (Limited Moisture Exposure) Table A-9.10.3.1.Bchange end
CSA O141-05 Softwood Lumber A-9.3.2.1.(1)
CSA O437.0-93 OSB and Waferboard A-9.23.15.4.(2)
CSA CAN/CSA-S6-06 Canadian Highway Bridge Design Code A-Table 4.1.5.3.
A-Table 4.1.5.9.
CSA S16-09 Design of Steel Structures A-4.1.5.11.
A-4.3.4.1.(1)
CSA S304.1-04 Design of Masonry Structures A-5.1.4.1.(5)(b) and (c)
CSA CAN/CSA-S406-92 Construction of Preserved Wood Foundations A-9.15.2.4.(1)
change beginCSA Z32-09 Electrical Safety and Essential Electrical Systems in Health Care Facilities A-3.2.7.6.(1)change end
CSA CAN/CSA-Z240 MH Series-09 Manufactured Homes A-1.1.1.1.(3)(3)
CSA Z240.2.1-09 Structural Requirements for Manufactured Homes A-1.1.1.1.(3)(3)
CSA Z240.10.1-08 Site Preparation, Foundation, and Anchorage of Manufactured Homes A-1.1.1.1.(3)(3)
CWC 1997 Introduction to Wood Building Technology A-9.27.3.8.(4)
CWC 2000 Wood Reference Handbook Table A-9.27.3.8.(4)
CWC 2009 The Span Book A-9.23.4.2.
CWC 2009 Engineering Guide for Wood Frame Construction A-9.4.1.1.
A-9.23.13.1.
EC CEPA 1988 Canadian Environmental Protection Act, Section 8, Part 1 A-6.2.1.7.(2)
EPA 625/R-92/016 (1994) Radon Prevention in the Design and Construction of Schools and Other Large Buildings A-5.4.1.1.
FM Approvals 2008 Approval Standard for Suppression Mode [Early Suppression – Fast Response (ESFR)] Automatic Sprinklers A-3.2.5.12.(7)
FPI Project 43-10C-024 (1988) Deflection Serviceability Criteria for Residential Floors A-9.23.4.2.(2)
HC 2004 Fungal Contamination in Public Buildings: Health Effects and Investigation Methods A-5.5.1.1.
HC 2008 Guide for Radon Measurements in Public Buildings (Schools, Hospitals, Care Facilities, Detention Centres) A-5.4.1.1.
A-6.2.1.1.
HC 2008 Guide for Radon Measurements in Residential Dwellings (Homes) A-9.13.4.3.
change beginHRAI SAR-G1 HRAI Digest 2005 A-9.36.3.2.(1)
A-9.36.3.2.(2)
A-9.36.3.4.(1)change end
change beginHVI HVI Publication 911-2012 Certified Home Ventilating Products Directory A-9.36.3.9.(3)change end
change beginICC 400-2007 Design and Construction of Log Structures A-9.36.2.2.(5)change end
ISO 7010:2003 Graphical symbols – Safety colours and safety signs – Safety signs used in workplaces and public areas A-3.4.5.1.(2)(c)
ISO 7731:2003(E) Ergonomics – Danger signals for public and work areas – Auditory danger signals A-3.2.4.22.(1)(b)
ISO 8201:1987(E) Acoustics – Audible emergency evacuation signal A-3.2.4.19.(2)
change beginNFPA 2010 Edition Fire Protection Guide to Hazardous Materials A-6.2.2.6.(1)change end
NFPA FPH 2008-2008 Fire Protection Handbook A-3.2.2.2.(1)
A-3.6.2.7.(5)
change beginNFPA 13-2013 Installation of Sprinkler Systems A-3.2.4.10.(3)(f)
A-3.2.5.12.(1)
A-3.2.5.12.(6)
A-3.2.5.12.(7)
A-3.2.5.13.(1)
A-3.2.8.2.(3)change end
change beginNFPA 13D-2010 Installation of Sprinkler Systems in One- and Two-Family Dwellings and Manufactured Homes A-3.2.5.12.(6)
A-3.2.5.12.(7)
A-3.2.5.13.(1)change end
change beginNFPA 13R-2010 Installation of Sprinkler Systems in Residential Occupancies up to and Including Four Stories in Height A-3.2.5.12.(6)
A-3.2.5.12.(7)
A-3.2.5.13.(1)change end
change beginNFPA 20-2010 Installation of Stationary Pumps for Fire Protection A-3.2.4.10.(3)(f)change end
change beginNFPA 30-2012 Flammable and Combustible Liquids Code A-6.2.2.6.(1)change end
change beginNFPA 30A-2012 Motor Fuel Dispensing Facilities and Repair Garages A-6.2.2.6.(1)change end
change beginNFPA 32-2011 Drycleaning Plants A-6.2.2.6.(1)change end
change beginNFPA 33-2011 Spray Application Using Flammable or Combustible Materials A-6.2.2.6.(1)change end
change beginNFPA 34-2011 Dipping and Coating Processes Using Flammable or Combustible Liquids A-6.2.2.6.(1)change end
change beginNFPA 35-2011 Manufacture of Organic Coatings A-6.2.2.6.(1)change end
NFPA 36-2009 Solvent Extraction Plants A-6.2.2.6.(1)
change beginNFPA 40-2011 Storage and Handling of Cellulose Nitrate Film A-6.2.2.6.(1)change end
NFPA 51-2007 Design and Installation of Oxygen-Fuel Gas Systems for Welding, Cutting, and Allied Processes A-6.2.2.6.(1)
change beginNFPA 51A-2012 Acetylene Cylinder Charging Plants A-6.2.2.6.(1)change end
change beginNFPA 55-2010 Compressed Gases and Cryogenic Fluids Code A-6.2.2.6.(1)change end
NFPA 61-2008 Prevention of Fires and Dust Explosions in Agricultural and Food Processing Facilities A-6.2.2.6.(1)
NFPA 68-2007 Explosion Protection by Deflagration Venting A-3.6.2.7.(5)
A-6.2.2.6.(1)
NFPA 69-2008 Explosion Prevention Systems A-3.6.2.7.(5)
A-6.2.2.6.(1)
change beginNFPA 72-2010 National Fire Alarm and Signaling Code A-3.2.4.22.(2)change end
change beginNFPA 80-2010 Fire Doors and Other Opening Protectives A-3.1.8.1.(2)
A-3.2.8.2.(3)change end
change beginNFPA 80A-2012 Protection of Buildings from Exterior Fire Exposures A-3change end
change beginNFPA 85-2011 Boiler and Combustion Systems Hazards Code A-6.2.2.6.(1)change end
change beginNFPA 86-2011 Ovens and Furnaces A-6.2.2.6.(1)change end
change beginNFPA 88A-2011 Parking Structures A-6.2.2.6.(1)change end
change beginNFPA 91-2010 Exhaust Systems for Air Conveying of Vapors, Gases, Mists, and Noncombustible Particulate Solids A-6.2.2.6.(1)change end
change beginNFPA 96-2011 Ventilation Control and Fire Protection of Commercial Cooking Operations A-3.3.1.2.(2)
A-6.2.2.6.(1)
A-9.10.1.4.(1)change end
change beginNFPA 101-2012 Life Safety Code A-3.3.2.1.(2)change end
change beginNFPA 204-2012 Smoke and Heat Venting A-6.2.2.6.(1)change end
change beginNFPA 303-2011 Marinas and Boatyards A-6.2.2.6.(1)change end
change beginNFPA 307-2011 Construction and Fire Protection of Marine Terminals, Piers, and Wharves A-6.2.2.6.(1)change end
change beginNFPA 409-2011 Aircraft Hangars A-6.2.2.6.(1)change end
NFPA 415-2008 Airport Terminal Buildings, Fueling, Ramp Drainage, Loading Walkways A-6.2.2.6.(1)
change beginNFPA 484-2012 Combustible Metals A-6.2.2.6.(1)change end
NFPA 654-2006 Prevention of Fire and Dust Explosions from the Manufacturing, Processing, and Handling of Combustible Particulate Solids A-6.2.2.6.(1)
change beginNFPA 655-2012 Prevention of Sulfur Fires and Explosions A-6.2.2.6.(1)change end
change beginNFPA 664-2012 Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities A-6.2.2.6.(1)change end
NFPA 1142-2007 Standard on Water Supplies for Suburban and Rural Fire Fighting A-3.2.5.7.(1)
change beginNFPA 1710-2010 Organization and Deployment of Fire Suppression Operations, Emergency Medical Operations, and Special Operations to the Public by Career Fire Departments A-3.2.3.1.(8)change end
change beginNLGA 2010 Standard Grading Rules for Canadian Lumber A-9.3.2.1.(1)
A-9.3.2.8.(1)
A-9.23.10.4.(1)change end
change beginNLGA SPS-1-2011 Fingerjoined Structural Lumber Table A-9.10.3.1.A
A-9.23.10.4.(1)change end
change beginNLGA SPS-3-2011 Fingerjoined 'Vertical Stud Use Only' Lumber Table A-9.10.3.1.A
A-9.23.10.4.(1)change end
NRCA 2005 The NRCA Waterproofing Manual A-5.6.2.1.
change beginNRCA 2011 The NRCA Roofing Manual: Membrane Roof Systems A-5.6.2.1.change end
NRC-IRC CBD 222 Airtight Houses and Carbon Monoxide Poisoning A-9.33.1.1.(2)
NRC-IRC CBD 230 Applying Building Codes to Existing Buildings A-1.1.1.2.(1)(3)
NRC-IRC CBD 231 Moisture Problems in Houses A-9.25.3.1.(1)
NRC-IRC 1988 Performance and Acceptability of Wood Floors – Forintek Studies A-9.23.4.2.(2)
NYCDOHMH 2008 Guidelines on Assessment and Remediation of Fungi in Indoor Environments A-5.5.1.1.
OMMAH 2006 2006 Building Code Compendium, Volume 2, Supplementary Standard SB-7, Guards for Housing and Small Buildings A-9.8.8.2.
change beginSMACNA ANSI/SMACNA 006-2006 HVAC Duct Construction Standards – Metal and Flexible A-9.36.3.2.(2)change end
change beginSMACNA 7th Edition Architectural Sheet Metal Manual A-5.6.2.1.change end
TC SOR/2008-34 Transportation of Dangerous Goods Regulations (TDGR) A-3.3.1.2.(1)
TWC 1993 Details of Air Barrier Systems for Houses Table A-9.25.5.1.(1)
TWC 1995 High-Rise Residential Construction Guide A-5.6.2.1.
ULC CAN/ULC-S101-07 Fire Endurance Tests of Building Construction and Materials A-3.1.5.12.(2)(e)
A-9.10.3.1.B
B-3.2.6.5.(6)(b)
ULC CAN/ULC-S112-M90 Fire Test of Fire-Damper Assemblies Table B-3.2.6.6.(1)C
ULC CAN/ULC-S113-07 Wood Core Doors Meeting the Performance Required by CAN/ULC-S104 for Twenty Minute Fire Rated Closure Assemblies A-9.10.9.3.(2)
A-9.10.13.2.(1)
ULC CAN/ULC-S124-06 Test for the Evaluation of Protective Coverings for Foamed Plastic A-3.1.5.12.(2)(e)
ULC ULC-S332-93 Burglary Resisting Glazing Material A-9.7.5.2.(1)
ULC CAN/ULC-S524-06 Installation of Fire Alarm Systems A-3.2.4.19.(8)
A-3.2.4.21.(7)
ULC CAN/ULC-S526-07 Visible Signal Devices for Fire Alarm Systems, Including Accessories A-3.2.4.20.(2)
ULC CAN/ULC-S572-10 Photoluminescent and Self-Luminous Signs and Path Marking Systems A-3.4.5.1.(4)
change beginULC CAN/ULC-S701-11 Thermal Insulation, Polystyrene, Boards and Pipe Covering A-9.36.2.4.(1)D.change end
change beginULC CAN/ULC-S702-09 Mineral Fibre Thermal Insulation for Buildings A-5.10.1.1.(1)
A-9.36.2.4.(1)D.change end
change beginULC CAN/ULC-S703-09 Cellulose Fibre Insulation (CFI) for Buildings A-9.36.2.4.(1)D.change end
change beginULC CAN/ULC-S704-11 Thermal Insulation, Polyurethane and Polyisocyanurate, Boards, Faced A-9.36.2.4.(1)D.change end
change beginULC CAN/ULC-S705.1-01 Thermal Insulation – Spray Applied Rigid Polyurethane Foam, Medium Density – Material - Specification A-9.36.2.4.(1)D.change end
change beginULC CAN/ULC-S712.1-10 Thermal Insulation - Light Density, Open Cell Spray Applied Semi-Rigid Polyurethane Foam - Material Specification A-9.36.2.4.(1)D.change end
change beginULC CAN/ULC-S741-08 Air Barrier Materials – Specification A-9.36.2.9.(1)change end
change beginULC CAN/ULC-S742-11 Air Barrier Assemblies – Specification A-9.36.2.9.(1)
A-9.36.2.10.(5)(b)change end
change beginULC CAN/ULC-S770-09 Determination of Long-Term Thermal Resistance of Closed-Cell Thermal Insulating Foams A-9.36.2.4.(1)D.change end
WCLIB No. 17 (2004) Standard Grading Rules A-Table 9.3.2.1.
change beginWWPA 2011 Western Lumber Grading Rules A-Table 9.3.2.1.change end
Notes to Table A-1.3.1.2.(1):
(1) Some documents may have been reaffirmed or reapproved. Check with the applicable issuing agency for up-to-date information.
(2) Some titles have been abridged to omit superfluous wording.
(3) Code reference is in Division A.

contentHistory